Bva-hydraulics HP1006 Manuale Utente Scaricare il pdf (Pagina 3)

Failure to comply with the following warnings may

result in personal injury as well as property

damage.

• Study, understand, and follow all instructions

provided with and on this device before use.

• Theusermustbeaqualiedoperatorfamiliarwith

the correct operation, maintenance, and use of cylinders.

Wear protective gear when operating

 hydraulicequipment.

 Thisdevice is NOT suitable for use as support

device! As the load is lifted, use blocking and cribbing

to guard against a falling load. Stay clear of a lifted

load before it is properly supported. Never rely on

hydraulic pressure to support a load.

Crush Hazard. Keep hands and feet away

from cylinder and workpiece during

operation.

• Do not exceed rated capacity of the cylinder or

  any equipmentinthe system. Thecylinderis

designed for a max. pressure of 10,000 psi.

•Do not connect a cylinder to a pump with higher pressure rating.

•Donotsubject cylinder to a shock loads,aloaddropped

suddenly, causing the system pressure to exceed rated

pressure.

 Thesystemoperatingpressuremustnotexceedthe

pressure rating of the lowest rated component

the system. Install a pressure gauge or other load

measuring instrument to monitor the operating pressure. Burst

hazard exists if hose, connection or any other component in the

system exceed its rated pressure.

Avoid damaging hydraulic hose. Do not allow hose

to kink, twist, curl, crush, cut or bend so tightly that

 uid ow within the hose is blockedorreduced.

Periodically inspect the hose for wear.

Do not pull, position or move cylinder setup by the

hose. Use carrying handle or other means of safe

transport.

Do not handle pressurized hoses. Never attempt to

grasp a leaking pressurized hose. Ensure to release

the system pressure before disconnecting hydraulic

hose or connections.

 Hydraulic uid can igniteandburn. Keep

hydraulic

 equipment awayfromames and heat.

Excessive

 heat will soften seals,resultingin uid leaks. Heat

also weakens hose materials.

Cylinder must be on a stable base which is able

to support the load while pushing or lifting. Use shims,

friction material or constrains to prevent slippage

of the base or load. Ensure cylinder is fully engaged

into/onto adapters, extension accessories.

Center load on cylinder. Distribute load evenly across

the entire saddle surface. Do not off-center loads on

 acylinder.The load can tip orthecylinder can

“kick out”.

Never try to disassemble a hydraulic cylinder, refer

 repairstoqualied,authorizedpersonal.ContactBVA

Hydraulics tech service for authorized service center.

 Donotsubject hose to sharpobjectsor heavy

impact.

Hose material or seals must not come in contact with

corrosive materials such as battery acid, creosote-

 impregnated objects andwetpaint. Never paint a

coupler or hose.

•

No alteration shall be made to the cylinder.

•

Use only factory authorized fasteners, accessories

  andhydraulicuid.

! WARNING

Heavy

INSTALLATION

NOTICE: Use an approved, high-grade pipe sealant to seal all

hydraulic connections.

Remove the dust cover and rubber plug from coupler

2. Inspectallthreadsandttingsforsignsofwearordamage,and

replaceasneeded.Cleanallthreadsandttings.

3. Connect hydraulic hose from hydraulic pump to the cylinder

coupler.Ensurethattherearenouidleaks.

4. Install in-line pressure gauge.

5. Check for leaks insystemand have repaired by qualified

personnel.

NOTICE: The use of cylinder attachments or extensions reduces

the cylinder capacity by at least 50% per attachment/extension.

WARNING: Before operating the pump, tighten all hose

connections with proper tools. Do not overtighten. Connections

should only be tightened securely and leak-free. Overtightening can

cause premature thread failure or high pressure ttings to burst.

WARNING: Before repairs are made, depressurize cylinder.

Tipsforhydraulichoses&uidtransmissionlines:

•Avoidshortrunsofstraightlinetubing.Straightlinerunsdonot

provide for expansion and contraction due to pressure and/or

temperature changes.

•Reduce stress in tube lines. Long tubing runs should be

supported by brackets or clips.

1 2 3 4 5 6 7 8 ... 23 24

Commenti su questo manuale

Nessun commento

Bva-hydraulics HP1006 Manuale Utente Pagina 3

Commenti su questo manuale

Prodotti e manuali riguardandi Apparecchiature Bva-hydraulics HP1006